SIMULATION -
JS Industries has expanded their business with the addition of their first remote office. The remote office router (R3) was previously configured and all corporate subnets were reachable from R3. JS Industries is interested in using route summarization along with the EIGRP Stub Routing feature to increase network stability while reducing the memory usage and bandwidth utilization to R3. Another network professional was tasked with implementing this solution. However, in the process of configuring EIGRP stub routing connectivity with the remote network devices off of R3 has been lost.
Currently EIGRP is configured on all routers R2, R3, and R4 in the network. Your task is to identify and resolve the cause of connectivity failure with the remote office router R3. Once the issue has been resolved you should complete the task by configuring route summarization only to the remote office router R3.
You have corrected the fault when pings from R2 to the R3 LAN interface are successful, and the R3 IP routing table only contains 2 10.0.0.0 subnets.
 
 
 
 
















 

Suggested Answer: See explanation below

First we have to figure out why R3 and R4 can not communicate with each other. Use the show running-config command on router R3.
 <img src="https://www.examtopics.com/assets/media/exam-media/02670/0004100001.png" alt="Reference Image" />
Notice that R3 is configured as a stub receive-only router. The receive-only keyword will restrict the router from sharing any of its routes with any other router in that EIGRP autonomous system. This keyword will also prevent any type of route from being sent. Therefore we will remove this command and replace it with the eigrp stub command:
R3# configure terminal R3(config)# router eigrp 123 R3(config-router)# no eigrp stub receive-only R3(config-router)# eigrp stub
R3(config-router)# end -
Now R3 will send updates containing its connected and summary routes to other routers. Notice that the eigrp stub command equals to the eigrp stub connected summary because the connected and summary options are enabled by default.
Next we will configure router R3 so that it has only 2 subnets of 10.0.0.0 network. Use the show ip route command on R3 to view its routing table:
 <img src="https://www.examtopics.com/assets/media/exam-media/02670/0004200001.png" alt="Reference Image" />
Because we want the routing table of R3 only have 2 subnets so we have to summary sub-networks at the interface which is connected with R3, the s0/0 interface of R4.
There is one interesting thing about the output of the show ip route shown above: the 10.2.3.0/24, which is a directly connected network of R3. We can't get rid of it in the routing table no matter what technique we use to summary the networks. Therefore, to make the routing table of R3 has only 2 subnets we have to summary other subnets into one subnet.
In the output if we don't see the summary line (like 10.0.0.0/8 is a summary"¦) then we should use the command ip summary-address eigrp 123 10.2.0.0
255.255.0.0 so that all the ping can work well.
In conclusion, we will use the ip summary-address eigrp 123 10.2.0.0 255.255.0.0 at the interface s0/0 of R4 to summary.
R4> enable R4# conf t -
R4(config)# interface s0/0 R4(config-if)# ip summary-address eigrp 123 10.2.0.0 255.255.0.0
Now we jump back to R3 and use the show ip route command to verify the effect, the output is shown below:
 <img src="https://www.examtopics.com/assets/media/exam-media/02670/0004300001.jpg" alt="Reference Image" />
Note: Please notice that the IP addresses and the subnet masks in your real exam might be different so you might use different ones to solve this question.
Just for your information, notice that if you use another network than 10.0.0.0/8 to summary, for example, if you use the command ip summary-address eigrp 123
10.2.0.0 255.255.0.0 you will leave a /16 network in the output of the show ip route command.
 <img src="https://www.examtopics.com/assets/media/exam-media/02670/0004300002.jpg" alt="Reference Image" />
But in your real exam, if you don't see the line "10.0.0.0/8 is a summary, Null0" then you can summarize using the network 10.2.0.0/16. This summarization is better because all the pings can work well.
Finally don't forget to use the copy run start command on routers R3 and R4 to save the configurations.
R3(config-if)# end -
R3# copy run start -
R4(config-if)# end -
R4# copy run start -
If the "copy run start" command doesn't work then use "write memory."

This question is in 300-101 Cisco Implementing Cisco IP Routing (ROUTE) Exam
For getting Cisco Certified Network Professional (CCNP) Routing and Switching Certificate




Disclaimers:
The website is not related to, affiliated with, endorsed or authorized by Cisco.
Trademarks, certification & product names are used for reference only and belong to Cisco.
The website does not contain actual questions and answers from Cisco's Certification Exam.